£ 
€ 
- Dry time (in-house tested): 12 - 24 Seconds (dependent upon setting used)
- Cost per 1000 dries: 28p - 64p (95.7 - 98% saving against paper towels)
- Guarantee: 5 Years
- Rated Power: 0.35 kW - 1.6 kW | 2.33 - 5.33 Wh per dry (Internal on / off heater switch and adjustable motor speed)
- Tax deductible through an Enhanced Capital Allowance (ECA) – on the Energy Technology List (ETL)
- Anti vandal screws, thick steel cover and solid back plate and will be good for around 900000+ cycles.
- Popular for its blue ray of light and LED triangle
- Noise and energy levels customisable to your own requirements – the motor speed can be reduced and the heater element switched off.
- Compact unit, takes up very limited wall space - W201mm x H277mm x D175mm.
- Fully harmonised CE certification – LVD, EMC and EMF; WEEE and ROHS approved.
- Available in polished chrome, brushed satin stainless steel and white steel.
- IP23
At Intelligent Hand Dryers UK, our ethos is to bring you as much open, honest and reliable information as possible so you can make the most suitable and informed purchase.
We endeavour to include independently obtained results and in house testing, as well as manufacturer's specifications. This gives a true reflection of dry time performance, noise and energy efficiency of each hand dryer.
Noise level testing was conducted at the Building Research Establishment (BRE) and a leading independent testing facility.
We also provide in house video testing to demonstrate dry performance. This gives a visual demonstration in “real use” as opposed to using methodical scientific protocols. The approximate dry time using this method was set when no spots of water could be seen on a paper towel after drying the hands. This is over and above what is required to be classed as a “hygienic dry” which requires 95% of the hands to be dry after using the dryer.
Need more information or advice? Please contact us by clicking here where one of our dedicated experts will be able to assist you in whichever way you need.
In our experience, the dry time stated by the manufacturer is not always the same in reality when used by the consumer. As experts in our field we like to show the types of variations we have found from independent testing and in house testing so that you have all relevant information before you purchase.
Turboforce | Dry Speed |
Stated by Manufacturer* | 10 – 12 seconds |
Independent testing+ | 16 seconds |
In house testing# | Approx. 12 seconds |
* As stated by the manufacturer using their own testing procedures
+ Please ask for more information
# Conducted using our own in house testing protocols (visual demonstration in “real use” as opposed to scientific protocols)
This hand dryer is one of the fastest on the market and our in house testing shows its excellent performance. The hand dryer compresses the airflow generated by the highly effective 18,000 rpm motor through a narrow air outlet ensuring the air is travelling at speeds of up to 100m/s!
To view our full range of fast drying hand dryers please click here
Not what you were looking for from a hand dryer? Have a look at our Intelligent Search Tool for a more personalised selection by clicking here
The energy efficiency of a hand dryer is derived by dividing the rated power by the dry speed. Ultimately what is important is how many watt-hours per dry are used.
TurboForce | Rated Power | Watt-hours per Dry |
Stated by Manufacturer* | 1.6kW | 4.44Wh – 5.33Wh |
Independent testing+ | N/A | N/A |
In house testing# | 1.6kW | 5.33Wh |
* As stated by the manufacturer using their own testing procedures
+ Please ask for more information
# Conducted using our own in house testing protocols (visual demonstration in “real use” as opposed to scientific protocols)
For comparison, a standard conventional hand dryer uses around 25 – 30Wh per dry.
The TurboForce is also RoHS approved which means every component is certified as recyclable and uses approximately 80% less energy than a conventional hand dryer.
The Turboforce has the ability to be able to manually reduce the motor speed and turn off the heater element. Both will significantly reduce the rated power of the unit, however will increase the amount of time it takes to dry the hands. The following rated powers can be achieved by manual adjustment:
| Motor Wattage | Element Wattage | Total Wattage |
High speed with Element on | 700W | 900W | 1600W |
Low Speed with Element on | 350W | 450W | 900W |
High Speed with Element off | 700W | NIL | 700W |
Low Speed with Element off | 350W | NIL | 350W |
To view our full range of our low energy hand dryers please click here
Not what you were looking for from a hand dryer? Have a look at our Intelligent Search Tool for a more personalised selection by clicking here
We are passionate about helping others reduce carbon emissions, which in turn will help slow down the negative effects of global warming. For more information about carbon emissions and the environment click here
The following table shows the approximate amount of carbon emissions produced to complete 1000 dries:
Turboforce | 2.88 Kg/CO2 per 1000 dries |
Paper Towels* | 22.5 Kg/CO2 per 1000 dries |
Standard warm air hand dryer+ | 13.5 Kg/CO2 per 1000 dries |
*Based on using 3 towels per dry
+Standard warm air hand dryer use approx 25 watts per dry
Paper towels are based on 22.5gms/Co2 per dry and standard warm air hand dryers are based on Carbon Trusts measurement of 1 kW = 0.54 kg/Co2.
To work out the annual running costs and carbon emissions in your facility for the Turboforce hand dryer click here – this will also show you how many virgin trees you will be saving by using this hand dryer compared to paper towels.
We are seriously committed, as a Carbon Trust accredited supplier, to provide you with the most eco-friendly hand dryers available. Please click here to see more about what we do to help improve the environment and reduce carbon emissions.
Not what you were looking for from a hand dryer? Have a look at our Intelligent Search Tool for a more personalised selection by clicking here
So how much will it cost you to run this hand dryer?
The below figures are per 1000 dries, please see below regarding how to calculate a more personalised annual cost for you:
Turboforce* | £0.64 |
Paper Towels+ | £12.50 |
Standard warm air hand dryer*# | £3 |
*Based on 12p per kW of electricity unit cost
+Based on 2.5 towels used per dry
#Standard warm air hand dryer use approx 25 watts per dry
Based on a 12p per kW of electricity unit cost, we would anticipate the Turboforce hand dryer would cost approximately £0.000640 per average drying cycle.
To work out the annual running costs and carbon emissions in your facility for the TurboForce hand dryer click here – this will also show you annual savings made against putting paper towels, roller towels and standard warm air hand dryers into your facility.
This hand dryer is one of the world’s most energy efficient, high speed hand dryers ensuring that your running costs will be kept to a minimum when compared to other forms of hand drying solutions.
Not what you were looking for from a hand dryer? Have a look at our Intelligent Search Tool for a more personalised selection by clicking here
Manufacturers typically measure sound levels in terms of decibels dB(A) @ a 1 metre distance in a sound proof chamber. This measurement does not take into account the increase in noise when hands are positioned under/in the dryer or when the sound bounces off walls. Where possible we supply manufacturer's stated dB(A), and 2 independent tests which are more reflective of 'real conditions’.
Manufacturer stated | 75 - 77dB(A) |
Hands under in an anechoic chamber (sound proof) | 84dB(A) |
Hands under in a normal room* | 93.7dB(A) |
*represents maximum “real life” volume
Equivalent Examples:
Normal Conversation 50 - 70dB(A)
Vacuum Cleaner 70dB(A)
Busy Traffic / Alarm clock 80dB(A)
Lawn Mower / Chainsaw 90dB(A)
*various internet sources
Please click here to read our guide to help understand what the perceived decibel level above would be equivalent to.
Although you can reduce the motor speed of the TurboForce to some degree, we would not class this hand dryer as being quiet. There is always going to be some trade off of performance when motor speed is reduced and the high speed nature of this unit keeps it being one of the best performing hand dryers on the market.
It is worth noting that if your noise concern relates to the noise carrying into different areas of the building then pitch will be just as relevant as sound output (loudness). Higher frequency pitches will not travel through walls as easily as low frequency pitches for example. Please contact usdirectly to discuss your specific need.
To view our full range of quiet hand dryers please click here
Not what you were looking for from a hand dryer? Have a look at our Intelligent Search Tool for a more personalised selection by clicking here
Washing hands correctly is the best way to ensure high levels of hand hygiene. Making sure hands are completely dry is the next important aspect of hand hygiene.
Most modern hand dryers have standard hygienic properties such as fast dry times and touch free sensors to activate. However for added peace of mind some models have enhanced hygienic properties.
The TurboForce includes both fast dry times and touch free sensors, however it doesn’t include any additional aspects that have been included to enhance hygienic properties.
To view our full range of hand dryers with extra hygienic properties please click here – this includes our eXtremeAir CPC model with Cold Plasma technology.
Not what you were looking for from a hand dryer? Have a look at our Intelligent Search Tool for a more personalised selection by clicking here
So how long will this dryer last?
Hand dryers can have 2 types of motor which are:
- A digital brushless motor
- A universal brush motor
In theory, universal brush motors do not last as long as digital brushless motors and require the brushes to be changed periodically. They also vary in their lifespan. Digital motors however do cost more to repair should they fail at any point. There are variations in the lifespans of both universal brushed motors and digital motors.
The best way to choose what is right for you is to look at your facility and the amount of use each hand dryer is expected to get. This way it can be determined if a brushed motor hand dryer would be most suitable for you or whether investing in a digital brushless motor would be more cost effective.
Type of motor in the Turboforce Hand Dryer | A universal brush motor | ||||
Lifetime of brushes before needing replacing (if applicable) |
| ||||
Lifetime of the motor |
|
* Please note: the above is for guidance only based on generalised information relating to standard figures; each location and type of usage will effect each factor. With all high speed brush motors, they will last longer if the dust around moving parts is removed periodically.
The Turboforce MARK II has recently been upgraded and now has an enhanced soft start motor which increases the life-span of the motor and the hand dryer’s efficiency.
With regards to the brushes, they are relatively inexpensive to purchase. In most situations you should expect to get 8 years plus use from the TurboForce Mark II. 6 monthly internal cleans by someone suitably trained to do so, following the guidelines in the manual, will help to prolong the life and maintain the performance of your hand dryer.
Based on the above information we would recommend this hand dryer to be situated in bathrooms with the following daily uses:
Low Traffic | Light Traffic | Medium Traffic | Heavy Traffic | Extreme Traffic |
<50 daily uses | 51 – 100 daily uses | 101 – 300 daily uses | 301 – 500 daily uses | 501> daily uses |
y | y | y | y | y |
To work out the annual life expectancy in your facility for the TurboForce hand dryer click here
To view our full range of long life expectancy hand dryers please click here
Not what you were looking for from a hand dryer? Have a look at our Intelligent Search Tool for a more personalised selection by clicking here.
Please note, you will need to make sure you have fuse spurs installed which are suitable for hand dryers.
The TurboForce hand dryer has our install rating of:
* 1 *
1 = Easy, simple installation with no complicated considerations
2 = Easy, simple installation with a few considerations
3 = Moderately complex installation, with some considerations
4 = Slightly difficult, possibly complex installation with some complicated considerations
5 = Difficult, complex installation with complicated considerations
Please click here to view the installation manual for Turboforce hand dryer.
Please note, our ratings above are our own for ease of comparison and are based on the assumption that a qualified electrician will be installing the hand dryer. We always recommend that a person of this calibre is commissioned to install for correct installation and health and safety requirements.
For more information regarding our install service please click here
Not what you were looking for from a hand dryer? Have a look at our Intelligent Search Tool for a more personalised selection by clicking here
Depending upon the location, hand dryers can be damaged through vandalism. This includes being leveraged off the wall, damaging the outer casing and putting foreign objects into the openings. Locations this is likely to occur include pubs, nightclubs, transport facilities such as train stations, schools, stadiums, arenas and unattended public toilets to name a few.
The Turboforce hand dryer has the following features to help reduce vandalism:
- Small compact size
- Limited outlets for foreign objects to be placed in to cause blockages
- Steel back plate and anti-vandal screws
- A thick (1.5mm) steel cover
- Smooth shape, not allowing for leverage to pull off the wall
The Turboforce’s design and added Anti-Vandal components make this a very robust and resilient hand dryer, suitable for all locations where vandalism may be possible.
To view our full range of hand dryers with enhanced anti vandal features please click here
Not what you were looking for from a hand dryer? Have a look at our Intelligent Search Tool for a more personalised selection by clicking here
There are a few points to consider when choosing a hand dryer with disabled users in mind. These include:
- Wheelchair access with regard to users being able to position their hands correctly
- The amount of moisture that will be left on the floor after drying if units are to be used by people physically impaired
- The noise level of some high speed hand dryers may be too loud for some users, such as users with autism, multiple sclerosis etc.
Disabled areas often double up as baby changing facilities, so considerations include leaving extra space for double buggies, noise levels for children etc.
The Turboforce hand dryer has the following features that may negate these concerns:
- “Hands under” type unit creating more accessibility and wider range of hand positions
The noise level of this hand dryer may not be suitable for some users and a more appropriate option may be needed.
To view our full range of hand dryers with suitable properties for disabled users please click here
Not what you were looking for from a hand dryer? Have a look at our Intelligent Search Tool for a more personalised selection by clicking here
Turboforce hand dryers are very similar to the Air-Fury hand dryer, the efast, the Ventaxia tempest, the Newlec Fast Dry, the Fast Dry and the Dolphin Velocity BC2001 hand dryer.
TurboForce high speed hand dryers look as good as any high performance hand dryer on the UK market and equal or better the performance of any hands under hand dryer. The Turboforce hand dryer is more compact than the Xlerator hand dryer, more robust than Airforce hand dryers and better value than either. For the majority of locations that want an energy efficient hand dryer, that will cope with the demands of all types of public use washroom, this is a great option.
If you like the ultra-cool UV light and want an even lower energy hand dryer, take a look at the G-Force hand dryers.
Some of the places this hand dryer has been installed include:
- London Olympic Stadium
- English Institute of Sport
- Motorpoint Arena, Sheffield
- Leeds Trinity University
- Manchester Airport
- Belfast Airport
- McDonalds restaurants
- London Museums
- Harry Ramsdens
- KFC
- Odeon Cinemas
- Santander
- Stirling University
- Sheffield City Hall
- Ponds Forge International Swimming Centre
- Hillsborough Leisure Centre
- Cherwell District Council
- Tropical Marine Centre
- The Alhambra Centre – Barnsley
Architect classification NBS is N13/472 Hand driers
Not what you were looking for from a hand dryer? Have a look at our Intelligent Search Tool for a more personalised selection by clicking here
| Energy Consumption | Electrical Supply Voltage | 230-240 Volts |
| Electrical Supply Frequency | 50/60 Hz | |
| Standby Power Consumption | <2 Watts | |
| Performance | Expected Motor Life | 3000 Hours |
| Dry Time (max setting) | 12 Seconds | |
| Dry Time Notes | In-house testing | |
| Universal Brush Motor | ||
| Motor Speed (max setting) | 18000 RPM | |
| Motor Speed (min setting) | 12000 RPM | |
| Air Speed (max setting) | 224 MPH | |
| Air Speed (min setting) | 168 MPH | |
| Air Volume (max setting) | 68.28 CFM | |
| Operating Temperature Range | Motor Thermal Protection auto resetting at 105 °C | |
| Heater Element Power | 0-900 Watts | |
| Motor Cutoff Time | 60 Seconds | |
| Motor Class | Class 1 | |
| Rated Power | Rated Power (max settings) | 1600 Watts |
| Rated Power (min settings) | 350 Watts | |
| Rated Power Notes | Adjustable motor speed and heater settings | |
| Energy Per Dry (max setting) | 5.33 Watts Watt-hours (Wh) | |
| Energy Per Dry (min setting) | 2.33 Watt-hours (Wh) | |
| Energy Per Dry Notes | Based on in-house testing dry times at Max settings | |
| Noise | Operating Sound Level (max setting) | 77 (manufacturer stated) dB |
| Sound Level Notes | Independently tested to be 84dB at max speed dB | |
| Sensor | Sensor type | IR |
| Guarantee | 5 Years | |
| Construction | Materials | Stainless steel, steel |
| Net Weight | 5.8 kg | |
| Packed Weight | 6.6 kg | |
| Finishes | White Steel | |
| Polished Chrome | ||
| Brushed Stainless Steel | ||
| Electrical & Safety | IP rating | IP23 |
| Dimensions | Product Height | 277 mm |
| Product Width | 201 mm | |
| Product Depth | 175 mm | |
| Packaging Height | 370 mm | |
| Packaging Width | 265 mm | |
| Packaging Depth | 225 mm | |
| Mounting Instructions | Men | 1170 mm |
| Women | 1120 mm | |
| Children 4-7 Years | 810 mm | |
| Children 7-10 Years | 910 mm | |
| Children 10-13 Years | 1020 mm | |
| Children 13-17 Years | 1120 mm | |
| Disabled | 940 mm | |
| Certification | CE | |
| UL | ||
| Other | TUV/GS Approved, CE marked in accordance with all the relevant EEC Harmonised Documents | |
| General | General Notes | RIBA Architect classification N13-472 hand driers/hand dryers Standard: EN 60335-1: 2012 & EN 60335-2-23: 2003 +A1:2008 +A11:2010 Type: high velocity air dryer Manufacturer: Intelligent Hand Dryers Product reference: Turboforce TF02 Operation: automatically activated Power rating: 350 - 1600W Enclosure: Steel Colour: Polished Chrome Fixing arrangement: Wall mounted with below unit access for rear entry cabling Electrical supply: Fused spur. |
For all spare parts for this hand dryer please click here or alternatively please see the table below.
Here is a list of spares and accessories available for the Turboforce® Hand Dryer
If you do not see the specific part you are looking for, please contact us
| Spare Part or Accessory | Part Code | Link to Product |
| Hand Dryer Red/Green LED Fly Lead | 449123 | Please click here |
| Hand Dryer Carbon Brush and Holder (pair) | 439733 | Please click here |
| Hand Dryer Heater Element Assembly | 438213 | Please click here |
| Hand Dryer Timer & Sensor Assembly | 409497 | Please click here |
| Hand Dryer Motor | 448833 | Please click here |
Service rating :Delivered really fast
Product : Excellent handwriting functions very well
Service rating :No issues with service, delivered shortly after payment
Product : These machines are smart looking and highly efficient, we're delighted with them.
Service rating :An excellent first service A++
Product : A Very good hand dryer, High speed, all for our staff team are very happy
There are working units on display if you want to try before buying. Buying? please call the branch inadvance to make sure stock is available.
Electricbase Aberdeen
Silverburn Pl
Bridge of Don
Aberdeen
AB23 8EG
T: 01224 258258
E: electricbase@aberdeen.co,uk
Electricbase Aylesbury
1 Rimmington Way
Aylesbury
HP19 8AW
T: 01296 619095
E: Aylesbury@electricbase.co.uk
Electricbase Belper
Viaduct Works
Gin Cl Way
Awsworth
Nottingham
NG16 2TA
T: 0115 938 7130
E: belper@electricbase.co.uk
Electricbase Bolton
Atlas Mill
Bentinck St
Chorley Old Rd
Bolton
BL1 4QG
T: 01204 498123
E: Bolton@electricbase.co.uk
Electricbase Boston
6 Tattershall Rd
Boston
PE21 9JG
T: 01205 318707
E: boston@electricbase.co.uk
Electricbase Bow
2 Dace Rd
Bow
London
E3 2NQ
T: 020 8221 5893
E: bow@electricbase.co.uk
Electricbase Chesterfield
Newbold Rd
Chesterfield
S41 7PB
T: 01246 293338
E: chesterfield@electricbase.co.uk
Electricbase Crawley
Stephenson Way
Crawley
RH10 1TN
T: 01293 652593
E: crawley@electricbase.co.uk
Electricbase Epsom (South West London)
Longmead Industrial Estate
2 Roy Richmond Way
Epsom
KT19 9AP
T: 01372 237883
E: epsom@electricbase.co.uk
Electricbase Glasgow
528 Blochairn Rd
Glasgow
G21 2DZ
T: 0141 559 5335
M: glasgow@electricbase.co.uk
Electricbase Grantham
S Parade
Grantham
NG31 6DD
T: 01476 583124
E: grantham@electricbase.co.uk
Electricbase Herne Bay
Sea St
Herne Bay
CT6 8JZ
T: 01227 743609
E: hernebay@electricbase.co.uk
Electricbase Leeds
1 Springwell Ct
Leeds
LS12 1AL
T: 0113 242 4089
E: leeds@electricbase.co.uk
Electricbase Lincoln
The Pelham House
Canwick Rd
Lincoln
LN5 8HG
T: 01522 559222
E: Lincoln@electricbase.co.uk
Electricbase Nantwich
Barony Employment Park
Beam Heath Way
Nantwich
CW5 6RG
T: 01270 611703
E: Nantwich@electricbase.co.uk
Electricbase Newark
Trent House
Appleton Gate
Newark
NG24 1QJ
T: 01636 675810
E: newark@electricbase.co.uk
Electricbase Nuneaton
Weddington Rd
Nuneaton
CV10 0AX
T: 024 7637 3686
E: Nuneaton@electricbase.co.uk
Electricbase Oxford
Watlington Rd
Oxford
OX4 6LN
T: 01865 787788
E: Oxford@electricbase.co.uk
Electricbase Portsmouth
Burrfields Rd
Portsmouth
PO3 5NA
T: 023 9262 3057
E: Portsmouth@electricbase.co.uk
Electricbase Scunthorpe
Rowland Rd
Scunthorpe
DN16 1ST
T: 01724 291034
E: scunthorpe@electricbase.co.uk
Electricbase Stoke
Meir Rd
Stoke
ST3 7JD
T: 01782 592701
E: stoke@electricbase.co.uk
Electricbase Sunderland
Thompson House
Commercial Rd
Sunderland
SR2 8QR
T: 0191 568 0100
E: sunderland@electricbase.co.uk
Electricbase Theale (Reading)
Kennet Weir Business Park
Arrowhead Rd
Theale
RG7 4AH
T: 0118 929 8920
E: theale@electricbase.co.uk
